Grey market parts
Does anybody have a good source for grey market Hitachi mini hoe parts?
View ArticleAftermarket windows for CAT 304C CR
Does anyone have a source for aftermarket windows for a CAT 304C CR. A recent house demo took out the cab door window and the cab window behind the open door. I also need the front flip up window from...
View ArticleKubota KX161 Stick Bushings
I went to replace the bushings and pin in the end of the stick today. When I took it apart, the bushings were loose in the bore and just fell out. There is about 1mm of wear in the bore. I assume that...
View ArticleWhich on do you recommend?
I need some help. I am ready to pull the trigger on a mini ex but I have two choices. I found a 03 kubota kx41-2v with 82 hours that I can buy for $13000 or a more used bobcat 322 with 1000 hours for...
View ArticleClik here to view.
New Mini Excavator
I have down sized a bit, and working in the domestic arena, chosen on a couple of key points, 4 year 4000 hr warranty, access both sides of the machine, which is good in tight places, same as a Yanmar...
View ArticleBobcat E35i hydraulic oil cooler air bleed port id?
Service manual instructions for changing hydraulic oil on the Bobcat E35i include bleeding air from a port on top of the hydraulic cooler. Good idea, neat little male port, very accessible; but the...
View ArticleLink Belt 80 Spin Ace
Any one on here have a LB Spin Ace in the 80 size? Looking for feedback good or bad.
View ArticleBobcat 331 - Slew not holding, bucket not overpowering thumb, foam in reservoir
My Bobby was acting odd today...while holding a log on a slight incline, the machine wanted to slew very slowly downhill while in idle. Normally, it holds position. Also noticed bucket curl couldn't...
View Articlerequesting to get the cat 307SSR workshop manual
Hello everybody. I am a new guy. I would like request all of you to give the cat 307SSR workshop manual. Please somebody give me the pdf for cat 307SSR workshop manual.
View Articlebobcat 442 says its overheating but its not
Recently bought a bobcat 442 (made by terex). As soon as you crank it the gauge goes straight to max temp and the overheat light comes on even if the machine has been sitting for days. I figured it was...
View ArticleWhich buckets do I need for my Bobcat E50?
Just ordered a new E50 (first mini excavator) to compliment my new T770, I plan to get a smooth lipped 36" for cleanup work. If I get one other bucket for digging, what is the best size? I was thinking...
View Article2005 cat 305 engine UPDATE!!!!!!
Engine rebuild update. I had a starting problem. Had to get injectors and high pressure pump rebuilt. I got the motor running tonite but I only have idle. When I turn the dial throttle stays the same...
View ArticleKubota KX91-2 Hydraulics
Hi All, I am new to this forum. I have an old Kubota Kx91-2. Its been sitting for a while but when I started it this morning only the tracks and blade are working. Not even a twitch from the other...
View ArticleV1505 kubota injection pump removal and installation
Could someone please provide me instructions on removal and installation of the injection pump on the 1505 kubota including the proper recommended bleeding of the fuel system and restarting of the...
View Articleterex tc50 hydraulic problem
Customer has a Terex TC50 excavator, ser # 0219. machine operates & fine for 15 - 20 minutes until oil warms up to operating temp. it then starts to slow operating speed until it quits operating or...
View ArticleJohn Deere 27c ZTS white or blue smoke?
Hello- I picked up this mini excavator this week and it's smoking a bit more than I'd like to see. It seems to start and run well. Here's a video of it running. I did drain the water separator before...
View ArticleCat 301.8 Radiator removal
Hi All, I have to remove the radiator from my excavator but I can't get it out. The bolts and hoses seem to be holding it in place. The operation and maintenance manual gives no real direction. If...
View ArticleDeere 35D Random Stalling, Fuel related?
Hey everyone, I recently purchased a Deere 35D, it runs great with the exception of this random stalling issue. When working with the machine it will randomly die out. Sometimes it fires right back up...
View ArticleVolvo EC15B the whole digger is swinging at arm move down
Hello, if the Arm is moving down slow or with medium Speed, the whole digger Begins to swing. This is only at the arm moving down, not at moving up. I checked, if the mechanical play is somewhere too...
View ArticleRPM adjusment
How can you determine where your rpms are on a mitsubshi 4cyl diesel engine. Im looking for 2600 rpms at wide open throttle. Machine has no tach. Thanks
View Article